Spring washers are commonly used in mechanical fastening systems where maintaining contact pressure and supporting joint stability are important. Among the traditional German specifications, DIN 127 and DIN 7980 are two frequently referenced standards for split spring lock washers. Although both feature a split ring structure, they differ in their intended applications, dimensions, and design characteristics.
Understanding these differences helps manufacturers, engineers, and purchasing teams select a suitable washer for their fastening assemblies. This article compares DIN 127 and DIN 7980 spring washers, explains their main characteristics, and discusses what to consider when specifying either type.
A DIN 127 spring washer is a split, helical metal ring designed with a gap and an offset between its ends. When installed beneath a nut or bolt head and compressed during tightening, the washer undergoes elastic deformation and produces a spring reaction.
DIN 127 includes different end configurations. Type A has tang ends, while Type B has square ends. Both belong to the traditional family of split spring lock washers with a rectangular cross-section.
These washers are commonly specified in general mechanical fastening applications. Their dimensions are selected according to the nominal thread size and the corresponding washer specification.
DIN 127 washers are available in various nominal sizes, making them suitable for different bolt and screw assemblies. Depending on the application, material options may include carbon spring steel and stainless steel. The material must provide appropriate mechanical properties for the required degree of compression and operating environment.
DIN 7980 specifies single-coil spring lock washers designed particularly for cheese head screws, also commonly referred to as cylindrical head screws. Their structure is similar to that of other split spring washers, but their dimensional design is intended to suit this specific fastener arrangement.
One important characteristic of DIN 7980 washers is their compact profile. Compared with corresponding DIN 127 washers, they generally have a smaller outside diameter and a different cross-sectional geometry. This makes them more suitable for fastening positions where the available bearing area is limited by the screw head or surrounding components.
DIN 7980 washers are traditionally used with cylindrical head screws in machinery, equipment, and mechanical assemblies. Their dimensions should be matched to the specified screw size rather than selected based only on the washer's visual appearance.

Although both standards describe split spring lock washers, their intended applications and dimensional characteristics are not identical.
| Comparsion Factor | DIN 127 Spring Washer | DIN 7890 Spring Washer |
| Basic structure | Split helical ring | Single-coil split ring |
| Cross-section | Rectangular | Square |
| Typical application | General bolted and screwed joints | Cheese head and cylindrical head screws |
| Outside diameter | Generally larger for comparable nominal sizes | Generally more compact |
| Installation space | Requires suitable bearing space | Designed for more restricted screw-head areas |
| Common materials | Carbon spring steel, stainless steel | Carbon spring steel, stainless steel |
The most important distinction is not simply the difference in overall size. DIN 127 is a more general spring washer specification, while DIN 7980 is specifically associated with cylindrical head screws.
For example, when a machine assembly uses a cylindrical head screw with limited space around the screw head, a DIN 7980 washer may provide a more suitable dimensional fit. A DIN 127 washer may be more appropriate when the assembly is designed around its corresponding dimensions and bearing area.
However, the two types should not be considered interchangeable without checking their dimensional and mechanical requirements.
Washer dimensions directly influence how the component fits into a fastening assembly. Three measurements are particularly important: inner diameter, outer diameter, and thickness.
Inner diameter (ID) determines whether the washer can fit over the screw or bolt without excessive clearance or interference. The opening should accommodate the nominal fastener size while meeting the relevant standard's dimensional tolerances.
Outer diameter (OD) determines the available bearing area beneath the screw head or nut. A larger outside diameter can provide a wider contact surface, but it also requires more installation space.
Thickness and cross-section influence the washer's geometry and deformation characteristics. A square-section DIN 7980 washer and a rectangular-section DIN 127 washer may respond differently under compression. Their mechanical performance should therefore be evaluated according to the applicable specification rather than assumed to be equivalent.
For accurate selection, engineers should refer to the relevant dimensional tables and confirm the actual measurements required by the assembly drawing.
Material selection affects spring washer hardness, elastic behavior, corrosion resistance, and service performance.
Carbon spring steel is commonly used when the washer needs suitable hardness and elastic recovery under compression. Heat treatment may be required to achieve the specified mechanical properties.
Stainless steel is another option, particularly for applications exposed to moisture or corrosive environments. However, stainless steel grades do not all have the same spring properties. The selected grade should be evaluated for its strength, hardness, and ability to withstand repeated or sustained loading.
For manufacturers producing these components through metal stamping, material thickness, forming accuracy, heat treatment, and dimensional inspection all contribute to consistent product quality.
Both washer types are traditionally classified as spring lock washers. Their elastic structure is intended to create a spring reaction when compressed in a fastening joint.
However, it is important not to assume that either type can reliably prevent loosening under every operating condition. Research and engineering practice have raised concerns about the effectiveness of conventional split spring washers, particularly in joints exposed to severe vibration or high dynamic loading.
Their suitability depends on factors such as joint stiffness, preload, surface conditions, fastener design, and operating environment. For critical applications, engineers should evaluate the complete fastening system and consider alternative locking methods where necessary.
A spring washer should not replace proper bolt preload design or a validated anti-loosening solution.
The choice between DIN 127 and DIN 7980 should begin with the fastener design. If the assembly uses cylindrical head screws and requires a compact washer profile, DIN 7980 is the specification to investigate. If the drawing calls for a DIN 127 washer, its specified type, dimensions, and material should be followed.
Before placing an order, confirm the nominal screw size, inner and outer diameters, thickness, material grade, hardness requirements, and surface finish. For applications with special installation constraints, custom dimensions may also need to be evaluated.
One additional point is important for new designs: DIN 127 and DIN 7980 are withdrawn standards. Their products remain available in the market and may still appear on existing engineering drawings, but buyers should verify the applicable specification and consider a current, validated fastening solution when developing new assemblies.
For metal stamping requirements, Jiashan Weiyue Fasteners Co., Ltd. manufactures components using carbon steel, stainless steel, copper, and aluminum. Spring washers and other stamped metal parts can be produced according to specified dimensions, drawings, and application requirements. Selecting the appropriate material and production specifications helps ensure that the finished washer matches the intended fastening design.